126 lines
3.0 KiB
Plaintext
126 lines
3.0 KiB
Plaintext
ONEAC(8)
|
|
========
|
|
|
|
NAME
|
|
----
|
|
|
|
oneac - Driver for Oneac UPS equipment
|
|
|
|
NOTE
|
|
----
|
|
|
|
This man page only documents the hardware-specific features of the
|
|
oneac driver. For information about the core driver, see
|
|
linkman:nutupsdrv[8].
|
|
|
|
SUPPORTED HARDWARE
|
|
------------------
|
|
|
|
This driver supports various Oneac UPS families:
|
|
|
|
- EG (late 80s, early 90s, plug-in serial interface card)
|
|
- ON (early and mid-90s, plug-in serial interface card)
|
|
- OZ (mid-90s on, DB-25 std., interface slot)
|
|
- OB (early 2000's on, big cabinet, DB-25 std., interface slot)
|
|
|
|
If your UPS is equipped with the Basic Interface card, use the
|
|
linkman:genericups[8] driver.
|
|
|
|
EXTRA ARGUMENTS
|
|
---------------
|
|
This driver supports the following optional settings in the
|
|
linkman:ups.conf[5] file:
|
|
|
|
*testtime*='num'::
|
|
Change battery test time from the 2 minute default.
|
|
|
|
*offdelay*='num'::
|
|
Change shutdown delay time from 0 second default.
|
|
|
|
INSTANT COMMANDS
|
|
----------------
|
|
This driver supports the following Instant Commands.
|
|
(See linkman:upscmd[8])
|
|
|
|
All UPS units
|
|
~~~~~~~~~~~~~
|
|
|
|
*shutdown.return*::
|
|
Turn off the load possibly after a delay and return when power is back.
|
|
|
|
*shutdown.stop*::
|
|
Stop a shutdown in progress.
|
|
|
|
*shutdown.reboot*::
|
|
Shut down the load briefly while rebooting the UPS.
|
|
|
|
*test.failure.start*::
|
|
Starts a 15 second long simulation of an input power
|
|
failure.
|
|
|
|
*test.battery.start.quick*::
|
|
Start a "quick" battery test. The default time is 2 minutes. This
|
|
time can be set in the *ups.conf* file. See *testime* above.
|
|
|
|
*test.battery.stop*::
|
|
Stops a battery test that is in progress.
|
|
|
|
All ON UPS units
|
|
~~~~~~~~~~~~~~~~
|
|
|
|
*reset.input.minmax*::
|
|
Reset the minimum and maximum input line voltage values
|
|
seen since the last reset or power on.
|
|
|
|
Newer ON UPS units
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
*test.panel.start*::
|
|
Start testing the UPS panel.
|
|
|
|
*test.battery.start.deep*::
|
|
Start a "deep" battery test. This test runs the UPS until the low
|
|
battery point and then returns to the AC line.
|
|
|
|
*reset.input.minmax*::
|
|
Reset the minimum and maximum input line voltage values
|
|
seen since the last reset or power on.
|
|
|
|
*beeper.enable*::
|
|
Enable UPS beeper/buzzer.
|
|
|
|
*beeper.disable*::
|
|
Disable UPS beeper/buzzer.
|
|
|
|
*beeper.mute*::
|
|
Mutes the UPS beeper/buzzer for the current alarm condition(s).
|
|
|
|
Writable Variables
|
|
------------------
|
|
See linkman:upsrw[8] to see what variables are writable for the UPS.
|
|
|
|
NOTE: If your UPS supports writing battery.runtime.low, the new set value
|
|
is to be entered in minutes (up to 99) but the reported value is reported
|
|
in seconds (set value * 60).
|
|
|
|
NOTE: If your UPS supports input.transfer.low and input.transfer.high,
|
|
those values are used to create an allowable output range. The UPS
|
|
will do what it can to keep the output voltage value within the
|
|
defined range (for example: tap change or switch to inverter).
|
|
|
|
AUTHOR
|
|
------
|
|
Bill Elliot <bill@wreassoc.com>,
|
|
Eric Lawson <elawson@inficad.com>
|
|
|
|
SEE ALSO
|
|
--------
|
|
|
|
The core driver:
|
|
~~~~~~~~~~~~~~~~
|
|
linkman:nutupsdrv[8]
|
|
|
|
Internet resources:
|
|
~~~~~~~~~~~~~~~~~~~
|
|
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
|