[Unit]
Description=Network UPS Tools - device driver for %I
After=local-fs.target

# Note: If the "Before" line below is uncommented, the target unit
# would only become initialized after the driver units are all in
# a final state (active, failed, ...) and would allow nut-server
# (upsd) to start up and represent those devices on the network.
# With this constraint commented away, the nut-server should start
# earlier, but may initially report some devices as Not connected
# (they should appear when drivers complete their initialization -
# e.g. snmp walks of large MIBs can take a while):
#Before=nut-driver.target

# Propagate stopping of the target:
PartOf=nut-driver.target

# Note: The choice of "network.target" allows to schedule this unit
# roughly when the network stack of this OS is ready (e.g. that the
# subsequent `upsd` will have a `0.0.0.0` or a `localhost` to bind
# to); however this target does not ensure availability of a real
# connection or final IP addresses. Drivers that require network as
# a media for interaction with UPSes (snmp-ups, netxml-ups, ipmi etc.)
# may want to extend this unit with `Requires=network-online.target`
# instead. Also note that *generally* this should not be a problem,
# since the drivers have a few retries with timeouts during startup,
# and typically by the time the box gets an IP address, the driver
# is still retrying to start and will succeed.
# Extending the unit does not require *this* file to be edited, you
# can instead drop in an additional piece of configuration, e.g. add
# a `/etc/systemd/system/nut-driver@.service.d/network.conf` with:
#   [Unit]
#   Requires=network-online.target
#   After=network-online.target
# If your `upsd` requires specific IP addresses to be available before
# starting, a `/etc/systemd/system/nut-driver.target.d/network.conf`
# can be used in a similar manner.
# Finally note that "nut-driver-enumerator.service" should take care of this.

[Service]
EnvironmentFile=-@CONFPATH@/nut.conf
SyslogIdentifier=%N
ExecStart=/bin/sh -c 'NUTDEV="`@NUT_LIBEXECDIR@/nut-driver-enumerator.sh --get-device-for-service %i`" && [ -n "$NUTDEV" ] || { echo "FATAL: Could not find a NUT device section for service unit %i" >&2 ; exit 1 ; } ; @SBINDIR@/upsdrvctl start "$NUTDEV"'
ExecStop=/bin/sh -c 'NUTDEV="`@NUT_LIBEXECDIR@/nut-driver-enumerator.sh --get-device-for-service %i`" && [ -n "$NUTDEV" ] || { echo "FATAL: Could not find a NUT device section for service unit %i" >&2 ; exit 1 ; } ; @SBINDIR@/upsdrvctl stop "$NUTDEV"'
# Restart really always, do not stop trying:
StartLimitInterval=0
Restart=always
# Protract the "hold-off" interval, so if the device connection is
# lost, the driver does not reapidly restart and fail too many times,
# and then systemd would keep the unit failed without further retries.
# Notably, this helps start "dummy-ups" drivers retranslating local
# devices (so getting a chicken-and-egg problem for driver-upsd-driver
# orderly series of initializations). More details in NUT issue #779.
RestartSec=15s
Type=forking
# Note: If you customize the "maxstartdelay" in ups.conf or in your
# NUT compilation defaults, so it exceeds the default systemd unit
# startup timeout (typically 90 sec), then make sure to set a slightly
# longer systemd timeout for the nut-driver unit instances. You can
# do this by populating a drop-in configuration, so it is not later
# overwritten by updates to your NUT package -- create a dir+file:
# /etc/systemd/system/nut-driver@.service.d/timeout.conf with lines:
# [Service]
# TimeoutStartSec=190s

[Install]
WantedBy=nut-driver.target