/* * apcsmart.h - common defines for apcsmart driver * * Copyright (C) 1999 Russell Kroll * (C) 2000 Nigel Metheringham * (C) 2011+ Michal Soltys * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #ifndef NUT_APCSMART_H_SEEN #define NUT_APCSMART_H_SEEN 1 #define DRIVER_NAME "APC Smart protocol driver" #define DRIVER_VERSION "3.2" #define ALT_CABLE_1 "940-0095B" /* * alerts and other stuff for quick reference: * * $ OL * ! OB * % LB * + not LB anymore * # RB * ? OVER * = not OVER anymore * * powering down now (only older models ?), handled by upsread() * otherwise ignored (it doesn't have to be in ignore sets) * * | eeprom change * & check alarm register for fail * ~ ??? */ /* * old ones for reference: * #define IGNCHARS "\015+$|!~%?=#&" * #define POLL_IGNORE "\015&|" * #define POLL_ALERT "$!%+#?=" * #define MINIGNCHARS "\015+$|!" * notice ~ that was present in IGNCHARS, but not in POLL_IGNORE - this kinda * didn't make sense (?); new versions doesn't filter ~, but keep that in mind * in case something obscure surfaces * due to switch to ICANON tty mode, we removed \015 from ignored characters, * as it's handled by IGNCR at read() level */ /* * about CR: * apparently windows is unable to ignore CRs by means of IGNCR flag (or * perhaps there is something else involved); so despite IGNCR we re-aad \015 * to ignore sets for now; see: * http://article.gmane.org/gmane.comp.monitoring.nut.user/7762 * * furthermore, since the canonical/non-canonical mode is user selectable now, * we have to ignore this character explicitly */ /* Basic UPS reply line structure */ #define ENDCHAR 10 /* APC ends responses with LF (and CR, but it's IGNCRed) */ /* what to ignore during alert aware serial reads */ #define IGN_AACHARS "\015|&" /* what alert_handler() should care about */ #define ALERT_CHARS "$!%+#?=" /* characters ignored by alertless reads */ #define IGN_CHARS IGN_AACHARS ALERT_CHARS /* * these ones are used only during Capability Check read, due to ^Z sending * certain characters such as #; it seems it could be equal to just IGN_CHARS * w/o # old: #define IGN_CCCHARS "|$!+" */ #define IGN_CCCHARS "\015|&$!%+?=" /* capability check ignore set */ /* * Command Set 'a' reports everything - protocol number, alerts and supported * commands */ #define IGN_CSCHARS "" /* command set ignore set */ /* dangerous instant commands must be reconfirmed within a 12 second window */ #define MINCMDTIME 3 #define MAXCMDTIME 15 /* it only does two strings, and they're both the same length */ #define APC_STRLEN 8 #define SER_D0 0x001 /* 0 sec., for flushes */ #define SER_DX 0x002 /* 200 ms for long/repeated cmds, in case of unexpected NAs */ #define SER_D1 0x004 /* 1.5 sec. */ #define SER_D3 0x008 /* 3 sec. (default) */ #define SER_AA 0x010 /* Alert Aware set */ #define SER_CC 0x020 /* Capability Check ign set */ #define SER_CS 0x040 /* Command Set ign set */ #define SER_TO 0x080 /* timeout allowed */ #define SER_HA 0x100 /* handle asterisk */ /* sets of the above (don't test against them, obviously */ /* * Some cmd codes to ignore (nut doesn't expose those, though the driver might * use them internally (e.g. [a]). If you decide to support them at some * point, remember about removing them from here ! */ #define APC_UNR_CMDS "\032\177~')-+8QRYayz" /* --------------- */ /* status bits */ #define APC_STAT_CAL (1L << 0) /* calibration */ #define APC_STAT_TRIM (1L << 1) /* SmartTrim */ #define APC_STAT_BOOST (1L << 2) /* SmartBoost */ #define APC_STAT_OL (1L << 3) /* on line */ #define APC_STAT_OB (1L << 4) /* on battery */ #define APC_STAT_OVER (1L << 5) /* overload */ #define APC_STAT_LB (1L << 6) /* low battery */ #define APC_STAT_RB (1L << 7) /* replace battery */ /* * serial protocol: special commands - initialization and such * these are not exposed as instant commands */ #define APC_STATUS 'Q' #define APC_GOSMART 'Y' #define APC_GODUMB 'R' #define APC_CMDSET 'a' #define APC_CMDSET_FMT "^[0-9]\\.[^.]*\\.[^.]+(\\.[^.]+)?$" #define APC_CAPS '\032' /* ^Z */ #define APC_NEXTVAL '-' #define APC_FW_OLD 'V' #define APC_FW_NEW 'b' #define APC_LBUF 512 #define APC_SBUF 32 /* default a.w.d. value / regex format for command '@' */ #define APC_AWDFMT "^[0-9]{1,3}$" /* sdtype method regex format*/ #define APC_SDFMT "^[0-5]$" /* advorder method regex format*/ #define APC_ADVFMT "^([0-4]{1,5}|[Nn][Oo])$" /* cshdelay format */ #define APC_CSHDFMT "^([0-9]\\.?|[0-9]?\\.[0-9])$" #endif /* NUT_APCSMART_H_SEEN */