100 lines
2.7 KiB
Plaintext
100 lines
2.7 KiB
Plaintext
|
UPSCODE2(8)
|
||
|
|
===========
|
||
|
|
|
||
|
|
NAME
|
||
|
|
----
|
||
|
|
upscode2 - Driver for UPScode II compatible UPS equipment
|
||
|
|
|
||
|
|
NOTE
|
||
|
|
----
|
||
|
|
This man page only documents the hardware-specific features of the
|
||
|
|
upscode2 driver. For information about the core driver, see
|
||
|
|
linkman:nutupsdrv[8].
|
||
|
|
|
||
|
|
SUPPORTED HARDWARE
|
||
|
|
------------------
|
||
|
|
This driver supports UPS equipment which can be controlled via the UPScode II
|
||
|
|
protocol. This is mainly Fiskars, Powerware equipment, but also
|
||
|
|
some (probably OEM'ed) products from Compaq.
|
||
|
|
|
||
|
|
EXTRA ARGUMENTS
|
||
|
|
---------------
|
||
|
|
This driver supports the following optional settings in the
|
||
|
|
linkman:ups.conf[5]:
|
||
|
|
|
||
|
|
*manufacturer*='value'::
|
||
|
|
Autodetection of this parameter is not possible yet (and it probably
|
||
|
|
never will be). Therefore, this user-defined string accepts any name. The
|
||
|
|
default is 'unknown'.
|
||
|
|
|
||
|
|
*input_timeout*='value'::
|
||
|
|
The timeout waiting for a response from the UPS. Some UPS models have
|
||
|
|
shown to be rather slow, resulting in frequent messages about empty
|
||
|
|
responses from the UPS. If you see this, try increasing this value.
|
||
|
|
|
||
|
|
*output_pace*='value'::
|
||
|
|
Delay between characters sent to the UPS. This was added for completeness
|
||
|
|
with the above parameter. It has not shown to be needed yet.
|
||
|
|
|
||
|
|
*baudrate*='value'::
|
||
|
|
The default baudrate is 1200, which is the standard for the UPScode II
|
||
|
|
protocol.
|
||
|
|
|
||
|
|
*full_update_timer*='value'::
|
||
|
|
Number of seconds between collection of normative values.
|
||
|
|
|
||
|
|
*use_crlf*::
|
||
|
|
Flag to set if commands towards to UPS need to be terminated with CR-LF,
|
||
|
|
and not just CR.
|
||
|
|
|
||
|
|
*use_pre_lf*::
|
||
|
|
Flag to set if commands towards to UPS need to be introduced with an LF.
|
||
|
|
A Compaq T1500h is known to need this.
|
||
|
|
|
||
|
|
COMMANDS
|
||
|
|
--------
|
||
|
|
|
||
|
|
The driver supports the following commands for those UPSen that support them.
|
||
|
|
The available commands are autodetected during initialization,
|
||
|
|
so you should check availability with 'upscmd -l'.
|
||
|
|
|
||
|
|
* test.panel.start - Start UPS self test
|
||
|
|
|
||
|
|
* test.battery.start - Start battery self test
|
||
|
|
|
||
|
|
* beeper.enable - Enable UPS beeper
|
||
|
|
|
||
|
|
* beeper.disable - Disable UPS beeper
|
||
|
|
|
||
|
|
* shutdown.return - Shut down in 1 second and wait for power to return
|
||
|
|
|
||
|
|
* shutdown.stayoff - Shut down in 1 seconds
|
||
|
|
|
||
|
|
* shutdown.reboot - Shut down in 1 seconds and reboot after 1 minute
|
||
|
|
|
||
|
|
* shutdown.reboot.graceful - Shut down in 20 seconds and reboot after 1 minute
|
||
|
|
|
||
|
|
NOTES
|
||
|
|
-----
|
||
|
|
|
||
|
|
The Powerware UPS models that this driver has been tested against until now
|
||
|
|
have not returned a value for 'battery.charge'. Therefore, the driver will
|
||
|
|
guestimate a value based on the nominal battery min/max and the current
|
||
|
|
battery voltage.
|
||
|
|
|
||
|
|
AUTHOR
|
||
|
|
------
|
||
|
|
Håvard Lygre <hklygre@online.no>,
|
||
|
|
Niels Baggesen <niels@baggesen.net>
|
||
|
|
|
||
|
|
SEE ALSO
|
||
|
|
--------
|
||
|
|
|
||
|
|
The core driver:
|
||
|
|
~~~~~~~~~~~~~~~~
|
||
|
|
linkman:nutupsdrv[8]
|
||
|
|
|
||
|
|
Internet resources:
|
||
|
|
~~~~~~~~~~~~~~~~~~~
|
||
|
|
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
|